 |  |
| |
As your Unix machine boots up, it will display a message for each device driver as it initializes. This is a good way to tell what devices your kernel was able to find. The exact output varies, but here is the output for hard drive controllers, hard drives, and network cards from a FreeBSD machine and a Debian Linux machine:
# FreeBSD
atapci0: <Intel ICH ATA66 controller> port 0xffa0-0xffaf at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
ad0: 19569MB <ST320430A> [39761/16/63] at ata0- master UDMA66
afd0: 239MB <IOMEGA ZIP 250 ATAPI> [239/64/32] at ata0-slave using PIO3
acd0: CDROM <ATAPI CDROM> at ata1-master using PIO4
rl0: <D-Link DFE-530TX+ 10/100BaseTX> port 0xbc 00-0xbcff
mem 0xefdfff00-0xefdfffff irq 11 at device 4.0 on pci1
# Linux
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
hda: WDC WD307AA-32BAA0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: WDC WD307AA-32BAA0, 29333MB w/2048kB Cache, CHS=3739/255/63, UDMA
Partition check:
hda: hda1 hda2 hda3
rtl8139.c:v1.07 5/6/99 Donald Becker
http://cesdis.gsfc.nasa.gov/linux/drivers/rtl8139.html
eth0: RealTek RTL8139 Fast Ethernet at 0xd400, IRQ 11, 00:50:ba:d3:9e:14.More specifically, in the line:
atapci0: <Intel ICH ATA66 controller> port 0xffa0-0xffaf at device 31.1 on pci0
atapci is the name of the device; 0 is the number of the device (devices are generally numbered sequentially with the first one probed getting the number 0); <Intel ICH ATA66 controller> is the name of the specific driver that successfully attached to this device; port 0xffa0-0xffaf at device 31.1 is physical address information about where this particular device is located; and finally, on pci0 tells us this device is attached to the first PCI bus (since pci is the device name of a PCI bus and 0 is the number assigned to the first PCI bus probed).
Note that in both FreeBSD and Linux, each line gives information about which driver is being used, hardware addresses, and options. Other platforms give similar information during boot. Often if you have a device that's not being recognized, you will see a line in the boot output telling you that a device was found but no driver for it could be found. If you would like more information, you may be able to boot your machine with boot -v from the bootstrap prompt -- the BSDs and Solaris support -v. This enables verbose booting, which prints out a lot more information during device probing and may help you understand why a device driver couldn't be found. Linux doesn't have any straightforward way to get verbose information like this, but you can use lspci to show every device on the PCI bus, whether there's an active driver for that device or not.
-- DJPH
|  | |
| 44. Devices |  | 44.3. Basic Kernel Configuration |
Copyright © 2003 O'Reilly & Associates. All rights reserved.