start page | rating of books | rating of authors | reviews | copyrights

Unix Power ToolsUnix Power ToolsSearch this book

45.2. Introduction to Printing on Unix

Unix used a print spooler to allow many users to share a single printer long before Windows came along. A user can make a printing request at any time, even if the printer is currently busy. Requests are queued and processed in order as the printer becomes available.

Unix permits multiple printers to be connected to the same system. If there is more than one printer, one printer is set up as the default printer, and print jobs are sent there if no printer is specified.

45.2.1. lpr-Style Printing Commands

Many systems use the lpr command to queue a print job. When you use lpr, it spools the file for printing.

$ lpr notes

The lpq command tells you the status of your print jobs by showing you the print queue for a given printer.

$ lpq
lp is ready and printing
Rank   Owner      Job  Files                Total Size
active fred       876  notes                7122 bytes
1st    alice      877  standard input       28372 bytes
2nd    john       878  afile bfile ...      985733 bytes

The word active in the Rank column shows the job that's currently printing. If your job does not appear at all on the listing, it means your job has finished printing or has been completely written into the printer's input buffer (or perhaps that you accidentally printed it to a different queue). If a job is not active, it's still in the queue.

You can remove a job with the lprm command. (Run lpq first to get the job number.)

$ lprm 877
dfA877host dequeued
cfA877host dequeued

The command lpc status (Section 45.3) can be used to determine which printers are connected to your system and their names. If there is more than one printer, you can then use the -P option with lpr, lpq and lprm to specify a printer destination other than the default. For instance, if a laser printer is configured as laserp, you can enter:

$ lpr -Plaserp myfile

If you'll be using a certain printer often, put its name in the PRINTER environment variable (Section 45.4).

If you're using an older system that has only lp (see below), or if you'd like a fancier lpr that supports all sorts of handy features, take a peek at LPRng (available at http://www.lprng.com). It supports everything standard lpr does and more, including a GUI for detailed configuration.

45.2.2. lp-Style Printing Commands

The System V-style print system, which Solaris uses by default, has the lp command to queue a print job. (Solaris also optionally includes lpr-style printing commands, if you install the BSD compatibility package.) When you use lp, it spools the file for printing and returns the request id of your print job. The request id can later be used to cancel the print job, if you decide to do so.

$ lp notes
request-id is lp-2354 (1 file)

The lpstat command can be used to check on the status of your print jobs. Like lpq, it will tell whether your job is in the queue or fully sent to the printer. Unlike lpq, it shows you only your own jobs by default:

$ lpstat
lp-2354          14519 fred     on lp

The message on lp indicates that the job is currently printing. If your job does not appear at all on the listing, it means your job has either finished printing or has been completely written into the printer's input buffer (or you accidentally printed it to a different queue). If the job is listed, but the on lp message does not appear, the job is still in the queue. You can see the status of all jobs in the queue with the -u option. You can cancel a job with the cancel command.

$ lpstat -u
lp-2354          14519 fred     on lp
lp-2355          21321 alice
lp-2356           9065 john
$ cancel lp-2356
lp-2356: cancelled

The lpstat command can be used to determine what printers are connected to your system and their names. If there is more than one printer, you can then use the -d option with lp to specify a printer destination other than the default. For instance, if a laser printer is configured as laserp, then you can enter:

$ lp -dlaserp myfile

If you'll be using a certain printer often, put its name in the LPDEST environment variable (Section 45.4).

-- DD, TOR, and JP



Library Navigation Links

Copyright © 2003 O'Reilly & Associates. All rights reserved.