Coding with mod_perl in Mind (Practical mod_perl)

This is the most important chapter of this book. In this chapter, we cover all the nuances the programmer should know when porting an existing CGI script to work under mod_perl, or when writing one from scratch.

This chapter's main goal is to teach the reader how to think in mod_perl. It involves showing most of the mod_perl peculiarities and possible traps the programmer might fall into. It also shows you some of the things that are impossible with vanilla CGI but easily done with mod_perl.

6.1. Before You Start to Code

There are three important things you need to know before you start your journey in a mod_perl world: how to access mod_perl and related documentation, and how to develop your Perl code when the strict and warnings modes are enabled.

6.1.1. Accessing Documentation

mod_perl doesn't tolerate sloppy programming. Although we're confident that you're a talented, meticulously careful programmer whose programs run perfectly every time, you still might want to tighten up some of your Perl programming practices.

In this chapter, we include discussions that rely on prior knowledge of some areas of Perl, and we provide short refreshers where necessary. We assume that you can already program in Perl and that you are comfortable with finding Perl-related information in books and Perl documentation. There are many Perl books that you may find helpful. We list some of these in Section 6.13 at the end of each chapter.

If you prefer the documentation that comes with Perl, you can use either its online version (start at http://www.perldoc.com/ or http://theoryx5.uwinnipeg.ca/CPAN/perl/) or the perldoc utility, which provides access to the documentation installed on your system.

To find out what Perl manpages are available, execute:

panic% perldoc perl

For example, to find what functions Perl has and to learn about their usage, execute:

panic% perldoc perlfunc

To learn the syntax and to find examples of a specific function, use the -f flag and the name of the function. For example, to learn more about open( ), execute:

panic% perldoc -f open

The perldoc supplied with Perl versions prior to 5.6.0 presents the information in POD (Plain Old Documentation) format. From 5.6.0 onwards, the documentation is shown in manpage format.

You may find the perlfaq manpages very useful, too. To find all the FAQs (Frequently Asked Questions) about a function, use the -q flag. For example, to search through the FAQs for the open( ) function, execute:

panic% perldoc -q open

This will show you all the relevant question and answer sections.

Finally, to learn about perldoc itself, refer to the perldoc manpage:

panic% perldoc perldoc

The documentation available through perldoc provides good information and examples, and should be able to answer most Perl questions that arise.

Chapter 23 provides more information about mod_perl and related documentation.

6.1.2. The strict Pragma

We're sure you already do this, but it's absolutely essential to start all your scripts and modules with:

use strict;

It's especially important to have the strict pragma enabled under mod_perl. While it's not required by the language, its use cannot be too strongly recommended. It will save you a great deal of time. And, of course, clean scripts will still run under mod_cgi!

In the rare cases where it is necessary, you can turn off the strict pragma, or a part of it, inside a block. For example, if you want to use symbolic references (see the perlref manpage) inside a particular block, you can use no strict 'refs';, as follows:

use strict;
{
    no strict 'refs';
    my $var_ref = 'foo';
    $$var_ref = 1;
}

Starting the block with no strict 'refs'; allows you to use symbolic references in the rest of the block. Outside this block, the use of symbolic references will trigger a runtime error.

6.1.3. Enabling Warnings

It's also important to develop your code with Perl reporting every possible relevant warning. Under mod_perl, you can turn this mode on globally, just like you would by using the -w command-line switch to Perl. Add this directive to httpd.conf:

PerlWarn On

In Perl 5.6.0 and later, you can also enable warnings only for the scope of a file, by adding:

use warnings;

at the top of your code. You can turn them off in the same way as strict for certain blocks. See the warnings manpage for more information.

We will talk extensively about warnings in many sections of the book. Perl code written for mod_perl should run without generating any warnings with both the strict and warnings pragmas in effect (that is, with use strict and PerlWarn On or use warnings).

Warnings are almost always caused by errors in your code, but on some occasions you may get warnings for totally legitimate code. That's part of why they're warnings and not errors. In the unlikely event that your code really does reveal a spurious warning, it is possible to switch off the warning.

Chapter 6. Coding with mod_perl in Mind

Contents:

6.1. Before You Start to Code

6.1.1. Accessing Documentation

6.1.2. The strict Pragma

6.1.3. Enabling Warnings


5.12. References		6.2. Exposing Apache::Registry Secrets